CONFAST 3/8'' x 6-1/2'' Galvanized Wedge Anchor (Box of 50)


CONFAST 3/8'' x 6-1/2'' Galvanized Wedge Anchor (Box of 50) by CONFAST at The Handyman Corner. MPN: WAG38612. Hurry! Limited time offer. Offer valid only while supplies last. ApplicationsThe anchor is made from Carbon Steel, and is Hot-Dipped Galvanized. This anchor is designed for use in Concrete only, and should never be used in block or brick base material. EnvironmentThe anchor is designed for use in a Damp environment.Hole Diameter/Bit DiameterThe anchor requires a 3/8'' hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.Diameter of Anchor The diameter o


CONFAST 3/8'' x 6-1/2'' Galvanized Wedge Anchor (Box of 50) by CONFAST
4.9 out of 5 stars with 7 reviews
Condition: New
Availability: In Stock
$82.99


Quantity:  

 


Product Description & Reviews

ApplicationsThe anchor is made from Carbon Steel, and is Hot-Dipped Galvanized. This anchor is designed for use in Concrete only, and should never be used in block or brick base material. EnvironmentThe anchor is designed for use in a Damp environment.Hole Diameter/Bit DiameterThe anchor requires a 3/8" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.Diameter of Anchor The diameter of the anchor is 3/8".Length Anchor The length of the anchor is 6-1/2"Thread LengthThe length of the threads on the anchor is 4" in length.Minimum EmbedmentThe minimum anchor embedment into the concrete is 1-1/2". Therefore, the anchor must be installed so that a minimum of 1-1/2" of the anchor is embedded into the concrete.Maximum Fixture ThicknessThe maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 4-5/8". This will ensure that the minimum embedment of 1-1/2" will be met.Fixture Hole DiameterThe hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/8" diameter anchor requires the hole in the fixture to be 1/2".Torque ValueTo be set properly in the concrete, the anchor must be torqued to between 25 - 30 ft./lbs.Spacing between AnchorsEach anchor must be spaced a minimum distance of 3-3/4" from each other when measured center to center.Edge DistanceIt is very important not to install the anchor any closer than 1-7/8" from an unsupported edge of the concrete.

Features & Highlights

  • HOT DIPPED GALVANIZED - Helps prevent rusting in moist environments
  • WIDE RANGE OF SIZES - Insures proper fastener for best results
  • PACKAGED WITH NUTS AND WASHERS - Fast, quick, complete installation
  • HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation

Additional Information

Brand:
CONFAST
Manufacturer:
CONFAST
Category:
Wedge Anchors
MPN:
WAG38612
Part Number:
WAG38612
Publisher:
CONFAST
Package Weight:
9.5 pounds
Package Size:
4.5 x 3.5 x 9 inches

 


Have questions about this item (WAG38612), or would like to inquire about a custom or bulk order?


If you have any questions about this product by CONFAST, contact us by completing and submitting the form below. If you are looking for a specif part number, please include it with your message.

First Name:
Last Name:
Email Address:
Your Message:

Related Best Sellers


mpn: WAS1212,
ApplicationsThe anchor is made from 304 Stainless Steel. This anchor is designed for use in Concrete only, and should never be used in block or brick base material. EnvironmentThe anchor is designed for use in a Wet environment.Hole Diameter/Bit Diam...

mpn: WAS12512,
ApplicationsThe anchor is made from 304 Stainless Steel. This anchor is designed for use in Concrete only, and should never be used in block or brick base material. EnvironmentThe anchor is designed for use in a Wet environment.Hole Diameter/Bit Diam...

mpn: WA1212,
ApplicationsThe anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material. EnvironmentThe anchor is designed for use in a Dry environment.Hole Diam...

mpn: 7242SD, ean: 0075352771946,
Powers Fasteners is the leading supplier of concrete and masonry anchors in North America and has been a leader in the fastening industry since 1921. Powers is an ISO-9001 international anchoring products company with extensive expertise in the follo...